Custom 50Mn Thin-Wall Slewing Bearing for CSM Machine | FDON Case
FDON Engineering Case · CSM Foundation Equipment

Custom 50Mn Thin-Wall Slewing Bearing for a 4-Ton Rotary Head

A non-standard internal-gear slewing bearing with an asymmetric cross-section, locally thin section and difficult welding interface — engineered to fit a compact Cutter Soil Mixing (CSM) rotary head where conventional bearing geometry was not suitable.

Send Drawing for Review →
CSM cutter soil mixing foundation machine using a custom FDON slewing bearing
Ø930 mmMaximum envelope OD
237 mmOverall assembly height
m8 / 103TInternal gear
50MnRing material
4 t / 6 mCustomer field validation
01 / The Engineering Problem

This Was Not a Standard Slewing Ring

The main difficulty was not simply diameter. The customer needed a highly customized ring that combined a thin and asymmetric section, an internal gear, a dense hole pattern and a welded machine interface. Each feature increased the risk of distortion, dimensional drift or installation error.

Challenge 01

Thin, Asymmetric Section

The drawing includes a locally reduced 26 mm upper flange/shoulder section. A tall, uneven cross-section has lower rigidity than a conventional compact ring, making machining and thermal distortion harder to control.

Challenge 02

Internal Gear Integration

The gear is module 8, 103 teeth, 20° pressure angle, x=0 with a Ø824 mm pitch diameter. Gear geometry and raceway geometry must remain concentric after the full manufacturing sequence.

Challenge 03

Complex Mounting Interface

The ring combines multiple bolt circles, tapped holes, counterbores, lifting/soft-zone/blockage positions and a sealing interface. The mounting geometry is part of the machine design, not an afterthought.

02 / Drawing Review

Key Dimensions & Interfaces

The following values are taken from the customer drawing supplied for this project.

Maximum outer envelopeØ930 mm
Upper outer diametersØ891.5 / Ø889.5 mm
Internal gear pitch diameterØ824 mm
Gear parametersm=8 · α=20° · z=103 · x=0
Referenced internal diameterØ810.88 mm
Rolling-element center diameterØ750 mm
Overall height237 mm
Local thin section26 mm (upper flange/shoulder)
Main tapped-hole pattern30 × M20-7H · face depth 45 · bottom hole 55
Counterbored mounting holes27 × Ø22 · counterbore Ø30 · depth 25
Additional threaded holes3 × M20-7H · depth 30
Seal specification750 × 780 × 15
Material50Mn

Drawing values are reproduced for this case study only. They should not be treated as a universal FDON standard size.

Technical drawing of custom thin-wall internal gear slewing bearing with 930 mm maximum envelope
Customer drawing — cross-section, internal gear and mounting-hole layout.
Highlighted 26 mm thin section in custom 50Mn slewing bearing drawing
The locally reduced 26 mm section increases sensitivity to clamping and welding distortion.
03 / Material & Welding Risk

Why 50Mn Needed a Different Installation Strategy

50Mn provides the strength, hardenability and wear-resistance response desired for heavy-duty slewing components, but it is considerably less weld-friendly than low-carbon structural steel.

  • Its higher carbon content / hardenability increases the risk of a hard and crack-sensitive heat-affected zone during uncontrolled welding.
  • Welding heat can introduce local shrinkage and distortion — especially dangerous on a thin, precision-machined ring.
  • Distortion can change fit, gear alignment and raceway geometry even when individual machined dimensions were correct before welding.
  • The connection should not rely on weld metal alone when the ring also acts as a precision rotating interface.
Custom 50Mn internal gear slewing bearing mechanically located and reinforced on CSM machine structure
Site integration of the customized slewing bearing with the fabricated rotary-head structure.
FDON recommendation: Bolt first. Weld second.We advised the customer to mechanically locate and reinforce the bearing with bolts before welding. This allowed the bolted interface to secure position and share load first, while welding became a secondary reinforcement operation rather than the only means of fixation.
“The difficult part was not making a Ø900 mm ring. It was keeping a thin, precision 50Mn ring in the right geometry after machining, installation and welding.”

Engineering note: any field welding on 50Mn should be performed under an appropriate qualified welding procedure. This case page describes the project strategy; it is not a universal WPS or welding instruction.

04 / Manufacturing Focus

Geometry Control Matters More as the Ring Gets Thinner

With this type of special cross-section, the manufacturing question is not only “Can we machine the dimensions?” It is “Will those dimensions still be correct after unclamping, gear machining, assembly and installation?”

Finished custom internal gear slewing bearings for CSM machine application
Finished internal-gear rings before final machine integration.
  • Machining sequence review: avoid unbalanced material removal that can release residual stress unevenly.
  • Clamping control: a thin section can be machined “round” while clamped and spring out after release if fixture force is excessive.
  • Gear/raceway relationship: preserve concentricity between the internal gear, rotating center and mounting interfaces.
  • Installation strategy: control the connection between the precision 50Mn ring and the welded structural frame.
  • Final fit verification: judge the bearing as part of the assembled rotary head, not as an isolated ring only.
05 / Customer Field Validation

A 4-Ton Rotary Head. Released From About 6 Meters.

After installation, the customer carried out an unusually severe field validation: the approximately 4-ton rotating power head was released from a height of about 6 meters. The customer reported that the bearing and machine interface showed very good fit and adaptability after the test.

~235 kJTheoretical gravitational potential energy before impact for 4,000 kg × 9.81 m/s² × 6 m. This number is shown only to illustrate the severity of the event.
PASSCustomer-reported fit/adaptability result after the field test and subsequent machine operation.

Important: actual impact force transmitted to the bearing depends on contact time, damping, structure, deformation and test setup. This was a customer field validation, not a standardized certified drop-test rating.

FDON slewing bearing factory video on YouTube Watch Factory Video
Customer field-operation footage of the CSM cutting/mixing head after installation.
06 / Project Evidence

From Drawing to Machine

The strongest proof in a custom bearing project is the complete engineering chain: drawing → manufactured ring → installation interface → operating machine.

07 / Engineering FAQ

Questions Engineers Usually Ask

What made this CSM slewing bearing difficult to manufacture?

The project combined a tall asymmetric cross-section, a locally thin 26 mm section, internal gearing, multiple mounting-hole systems and an interface that had to be integrated with a welded rotary-head structure. These features increase sensitivity to clamping, residual stress, machining sequence and installation distortion.

Why was 50Mn used?

50Mn is commonly selected for heavy-duty slewing components because it can provide useful strength, hardenability and wear resistance after appropriate heat treatment. In this project, however, the same metallurgy made direct welding more difficult than with ordinary low-carbon structural steel.

Why not simply weld the 50Mn ring directly to the structure?

Direct welding can create a hard heat-affected zone, crack risk and thermal distortion. For a precision thin-wall ring, even small distortion can affect fit and alignment. FDON therefore recommended mechanically locating and reinforcing the interface with bolts first, then using welding as a secondary reinforcement operation under a suitable procedure.

What were the main gear parameters?

The customer drawing specifies an internal gear with module 8, 103 teeth, 20° pressure angle, zero profile shift and a Ø824 mm pitch diameter.

How was the final solution validated?

According to the customer, the approximately 4-ton rotary power head was subjected to a field drop/release from about 6 meters and the product showed very good fit and adaptability. The machine was subsequently operated in the field. This customer validation should not be interpreted as a standardized impact-load certification.

Have a Thin-Wall or Difficult Custom Slewing Bearing?

Send FDON your drawing, model number or application details. We can review manufacturability, material risk, mounting interfaces and replacement options before quotation.

Send Drawing → steven@slewingbearings.com Visit FDON Slewing Bearings