Slewing Bearing for Offshore Wind | Esbjerg, Denmark Engineering Case | FDON

Denmark | Offshore Wind (Esbjerg)

North Sea loads. Salt air. Zero room for a weak joint.

Offshore wind equipment serviced from Esbjerg works under moving loads, wind, spray and long maintenance intervals. The slewing bearing must carry the moment, resist corrosion and keep the bolted interface stable for years.

OFFSHORE WIND · ESBJERG, DENMARKLoad path → hook → boom → slewing bearing → structure → vessel / platformSLEWING BEARINGSERVICE CRANE
Offshore is a different load case.The bearing sees moment, motion and corrosion at the same time — plus a bolt joint that must hold for years.
EsbjergDanish offshore wind port
North SeaOperating environment
C5 / CXCorrosivity classes
2 t @ 8 mExample crane case
≈ 220 kNmExample factored moment

01 / Application context

Esbjerg is the base.
The North Sea is the load case.

Esbjerg is one of Denmark's main ports for offshore wind construction, logistics and service. Equipment connected to this work — turbine yaw and pitch systems, nacelle and platform cranes, vessel-mounted lifting and access systems — rotates under combined axial, radial and overturning loads while exposed to wind, spray and continuous vibration.

For FDON, the question is not only “What is the maximum moment?” It is “What happens to the raceway, gear, seals and bolts after years of salt, motion and limited maintenance access?”

02 / First engineering check

Start with what can be calculated.
Then add what the sea changes.

01 / EXAMPLE LIFT

Safe working load

2,000 kg × 9.81 ≈ 19.6 kN of vertical hook load. This is an illustrative input; replace it with the real project value.

02 / STATIC MOMENT

Load at 8 m radius

19.6 kN × 8 m ≈ 157 kNm of static overturning moment from the hook load alone, before boom and structure weight.

03 / DYNAMIC FACTOR

Offshore motion allowance

157 kNm × 1.4 ≈ 220 kNm. The 1.4 factor is an example; the real factor comes from the applicable crane / offshore standard and motion data.

Example hook load2 t / 19.6 kN
Example working radius8 m
Static hook moment≈ 157 kNm
Example factored moment≈ 220 kNm
Mk = (m × g × R) × dynamic factor = (2,000 × 9.81 × 8) × 1.4

Why this still is not the final bearing load

The hook moment is only one part of Mk. Boom and structure weight, their centers of gravity, wind, vessel or platform motion, slewing acceleration and out-of-plumb conditions all add to the load at the bearing. Axial load Fa and radial load Fr must be determined together with the moment.

Engineering boundary: the numbers above are a worked example, not a project result. Do not select a bearing from hook load alone; use the full load case and the applicable design standard.

03 / Marine environment review

Static capacity is only
the first gate.

For offshore wind, the rotary joint should be reviewed as a complete system. Raceway, seal, grease, coating, gear and bolted interface all age in the same environment.

01

Load spectrum & fatigue

Confirm Fa, Fr and Mk with dynamic factors, including worst boom position, motion and the expected number of load cycles.

02

Corrosion protection

Agree the corrosivity class and coating system on the drawing. Protect exposed surfaces, gear teeth, bolt holes and ring faces.

03

Seals & lubrication

Choose seal material and grease for salt spray, temperature range and realistic relubrication access offshore.

04

Mounting bolts

Specify bolt grade, protection and controlled preload. Vibration and corrosion both threaten long-term preload retention.

05

Low-temperature behavior

Check ring material toughness and grease behavior at the minimum design temperature for the site and transport.

06

Documentation

Material certificates, hardness, runout, clearance and gear inspection reports should be tied to the approved drawing and project requirements.

04 / Bearing interface

Choose the bearing type
from the full load case.

Single-row four-point contact designs are compact for combined loading, while higher moments or stiffness demands may need a double-row or three-row roller solution. The final choice should be checked against the static limiting-load curve, the dynamic case and the bolt curve, not only the outside diameter.

Explore FDON four-point contact slewing bearings ↗

Technical support center ↗

Design itemWhy it matters in offshore wind service
Raceway capacityPlot the factored Fa / Mk operating point on the bearing load curve with the required safety factor.
Surface protectionCoating system and class must suit salt spray, humidity and the planned maintenance interval.
Seals & greaseSeal compound and grease must tolerate spray, temperature range and slow oscillating motion.
Bolt circle & gradeThe bolt joint can govern before the raceway in high-moment service; corrosion protection is part of the check.
Support stiffnessFlatness and stiffness of the mounting structure strongly affect clearance and raceway contact.
InspectionRunout, hardness, clearance and gear checks should be recorded against the approved drawing.

05 / Engineering conclusion

What we can say now — and what still needs data.

Supported by the worked example

A 2 t hook load at 8 m radius gives about 157 kNm of static moment, and about 220 kNm with an example 1.4 dynamic factor. This shows the calculation route and a first reference to compare with a candidate bearing's limiting-load curve.

Required before final approval

Provide the maximum Fa, Fr and Mk including dynamic factors. If not available, provide boom and structure weights, centers of gravity, working radius, motion data, duty cycle, design life, corrosivity class and mounting-structure details.

This page is an application engineering study with illustrative inputs, not a claim of project-specific certification. The machine builder remains responsible for validating the complete structure, standards compliance and operating duty.

06 / Engineer FAQ

Questions that matter
before production.

These items decide whether a promising static check becomes a robust offshore rotary joint.

Is a static capacity check enough for offshore wind?

No. Dynamic factors, fatigue cycles, corrosion and low temperature must be added to the static check before approval.

Is the hook load the only source of overturning moment?

No. Boom and structure weight, wind, motion, slewing acceleration and out-of-plumb conditions also contribute to the moment at the bearing.

What corrosion protection should be specified?

Specify the corrosivity class, coating system, seals, grease and fastener protection on the approved drawing, following the project standard.

What should be included in the final drawing review?

Mounting dimensions, hole pattern, gear data, material and heat treatment, clearance, runout, bolt grade and preload, sealing, coating, lubrication and the required inspection report.

07 / Review your offshore wind application

Send the rotary-joint data.
We will start with the load path.

For a new design or a replacement, send the bearing / assembly drawing and the load case. We can review the slewing bearing, gear interface, protection requirements and the information still needed for a reliable quotation.

Email Steven ↗

Minimum engineering brief

Equipment
Type, working radius, rated load, working positions
Loads
Maximum Fa, Fr and Mk including dynamic factors
Motion
Rotation angle, speed, oscillation or continuous duty, cycles
Interface
OD / ID / height, bolt circles, gear data, mounting-face thickness
Environment
Corrosivity class, temperature range, spray exposure, lubrication access
Standards
Design life, certification, material certificates, inspection report